Peripherals Archives

The DDMA is a four-channel Direct Memory Access Controller. Its purpose is to transfer data between memories and peripherals...

+ 4 independent DMA channels supporting bi-directional data transfers

+ Supports Memory-Memory, Memory-Peripheral & Peripheral-Memory

+ Up to 16MB transaction size

Our efficient Core performs serial to parallel conversion on data received from an IR Receiver Diode. The processor can...

+ Two working modes

+ Support of many IR protocols

+ Fault detection and interrupts

The DPSMBUS is a fully-featured module based on the I2C protocol, which supports SMBus and PMBus functionalities. It can...

+ Conforms to v3.1 SMBus & 1.3.1 PMBus specification

+ Supports all SMBus & PMBus communication sequences

+ Performs arbitration & clock synchronization

D16950 bridge to APB, AHB, AXI bus, it is a soft core of a Universal Synchronous and Asynchronous Receiver/Transmitter (UART),...

+ The most powerful UART IP Core

+ Compatible to the OX16C950

+ Programmable Baud Rate Generator

DOSPI bridge to APB, AHB, AXI bus, it is a revolutionary octal SPI designed to offer the fastest operations available...

+ The fastest available operations

+ For any serial SPI memory

+ Supports all 8, 16, 32-bit CPUs

DFSPI bridge to APB, AHB, AXI bus, it is a fully configurable SINGLE, DUAL, QUAD and OCTAL SPI master/slave...

+ Set of software accessible control registers to execute any Flash memory command

+ Supports any device clock frequency, polarity and phase

+ Programmable baud rate generator

DQSPI bridge to APB, AHB, AXI bus, it is a revolutionary quad SPI designed to offer the fastest operations available...

+ The fastest available operations

+ For any serial SPI memory

+ Supports all 8, 16, 32-bit CPUs

The DESPI is a fully configurable eSPI master/slave device supporting all features described in Enhanced Serial Peripheral Interface Base...

+ The fastest available operations

+ For any serial SPI memory

+ Supports all 8, 16, 32-bit CPUs

DMAC-RMII bridge to APB, AHB, AXI bus, our innovative solution is a hardware implementation of media access control protocol...

+ Conforms to IEEE 802.3-2002 spec

+ Provides static configuration of PHY IC

+ Half and full duplex supported

DCAN FD bridge to APB, AHB, AXI bus, it is a standalone controller for the Controller Area Network (CAN),...

+ In accordance to ISO 11898-1:2015

+ Supports CAN 2.0B and CAN FD frames

+ Overcomes standard CAN limits

DHDLC bridge to APB, AHB, and AXI bus, provides versatile support for a widely used HDLC transmission protocol. It...

+ Receiver and transmitter interfaces

+ Supports CRC16 and CRC32

+ Bit stuffing and unstuffing

D16450 bridge to APB, AHB, AXI bus, it is a soft core of the Universal Asynchronous Receiver/Transmitter (UART), functionally identical...

+ Functionally identical to the TL16C450

+ Configuration capability

+ Exact transmission rate

D16550 bridge to APB, AHB, AXI bus, it is a soft Core of Universal Asynchronous Receiver/Transmitter (UART), functionally identical...

+ Supports RS232 and RS485 standards (optional)

+ APB, AXI, AHB and more bus standards

+ Modem functionality supported

D16750 bridge to APB, AHB, AXI bus, it is a soft Core of a Universal Asynchronous Receiver / Transmitter...

+ Supports RS232 and RS485 standards

+ Hardware data flow control

+ APB, AHB AXI and more bus standards supported

D16752 bridge to APB, AHB, and AXI bus, it is a universal asynchronous receiver/transmitter (UART) with 64-byte FIFOs and automatic...

+ Software compatible with TL16C752

+ Selectable hardware flow control

+ Selectable software flow control

D2698 bridge to APB, AHB, AXI bus, it is an Octal UART Core software compatible with the SC2698. The...

+ SCC2698 compatible

+ 8 full-duplex independent asynchronous receiver/transmitters

+ Transmitter channels in a single package

D2692 bridge to APB, AHB, AXI bus, it is a dual channel UART Core, software compatible with SC26C92, SCC2692...

+ SC26C92, SCC2692, SCN2681 compatible

+ Two full-duplex asynchronous receiver

+ Transmitter channels in a single package

The D6840 is a programmable timer module compatible with the 6840 industry standard. It was designed to be used in...

+ Compatible with 6840 standard

+ Three separate timers

+ Three separate 16-bit timers

The D8254 is a programmable interval timer/counter, binary compatible with the 82C54 industry standard. Since DCD’s core value is innovation,...

+ Generation of accurate time delays

+ Under software control

+ Fully automated testbench

The D8255 is a programmable I/O device designed for use with all Intel CPUs. What’s significant, it also supports...

+ Compatible with industry standard 8255

+ Programmable I/O device

+ Three major operating modes

DI2S bridge to APB, AHB, AXI bus, it is a universal solution which provides an interface between a microprocessor...

Configurable number of independent audio modules with their respective FIFO

Configurable TX/RX mode of each audio module

Configurable master/slave mode support of each audio module

DSMART bridge to APB, AHB, AXI bus, it is a fast, versatile and cost-competitive core intended for smart card...

+ Compatible with the ISO 7816-3:2006

+ Support for EMV 4.2/4.3 standard

+ Works with all major CPUs

The D8259 is a soft Core of Programmable Interrupt Controller, fully compatible with the 82C59A device. Our efficient IP...

+ Support for all 82C59A modes features

+ 8 vectored priority interrupts

+ Up to 64 vectored priority interrupts

The I3C (Improved Inter-Integrated Circuit) is the successor of the I2C bus. Keeping the best assets from its elder...

+ MIPI I3C specifications with Host Controller Interface (HCI) v1.1 specification

+ Master transmitter

+ Master receiver

The DUTS stands for DCD’s Universal Timers System. It is a programmable and highly configurable device that comprises seven...

+ Three software selectable clock sources

+ Software selectable polarity of output waveform

+ Works with all major CPUs

D8530 bridge to APB, AHB, AXI bus, it is a dual-channel USART (Universal Synchronous/Asynchronous Receiver/Transmitter) device, designed for use...

+ Software compatible with Z85C30

+ Dual channel USART

+ Handles IBM® Bisync and...

DMESCC – Dual channel Multiprotocol Enhanced Serial Communication Controller, is designed for use with 8- and 16- bit microprocessors....

+ Software compatible with Z85C30

+ multiprotocol combo: HDLC, UART, SPI

+ Handles IBM® Bisync and...

DCD-SEMI believes that even though something may be small or slow, it can still offer maximal efficiency and ultimate reliability. That’s why...

+ Conforms to LIN 1.2, 2.1, 2.2A spec

+ Automatic LIN Header handling

+ Automatic Re-synchronization

DMAC bridge to APB, AHB, AXI bus. The Ethernet specification served as the basis for the 802.3 standard, which...

+ Conforms to IEEE 802.3-2002 spec

+ Configurable width CPU interface

+ Simple interface=easy connection to CPU

DSPI bridge to APB, AHB, AXI bus, it is a fully configurable SPI master/slave device, which allows you to...

+ Master & Multi-master operations

+ 8 SPI slave select lines

+ System error detection

DμART bridge to APB, AHB, AXI bus, it is a soft core of a Universal Asynchronous Receiver/Transmitter (UART). It...

Majority Voting Logic

Adds or deletes standard asynchronous communication bits (start, stop, and parity) to or from serial data

In UART mode receiver and transmitter are double buffered to eliminate the need for precise synchronization between the CPU and serial data

Featured products

DAES bridge to APB, AHB, AXI bus, it is a cryptographic co-processor which implements Rijndael encryption algorithm compliant with...

+ Support for 128 and 256 key bit length

+ Support for ECB, CBC, CFB, OFB, CTR block cipher modes

+ Internal key expansion module

DSHA2-256 bridge to APB, AHB, AXI bus, it is a universal solution which efficiently accelerates SHA2-256 hash function compliant...

+ FIPS PUB 180-4 compliant SHA2-256 function

+ RFC 2104 compliant HMAC native mode support

+ SHA2 224 and 256 bit modes support

The DF6808 is an advanced, 8-bit, MCU IP Core with highly sophisticated, on-chip peripheral capabilities. The DF6808 soft core is binary-compatible...

+ binary-compatible with Motorola 68HC08

+ 3.2 times faster than the original

+ fully customizable

DCAN FD bridge to APB, AHB, AXI bus, it is a standalone controller for the Controller Area Network (CAN),...

+ In accordance to ISO 11898-1:2015

+ Supports CAN 2.0B and CAN FD frames

+ Overcomes standard CAN limits

Stay tuned

IP Core IP Core

SPI: These Three Letters Denote Everything You Asked For

Electronics are everywhere. Many times, as frequent users, we do not even notice a “paradigm change” in the things...

Technology

DCD and Resquant are ready for quantum computing-resistant cryptography

NIST, the U.S. Department of Commerce’s National Institute of Standards and Technology has just announced (July the 5th, 2022)...

IP Core

DCD-SEMI adds extra features to LIN IP Core and GuardKnox license the solution

DCD-SEMI, a leading IP Core provider and SoC design house from Poland, mastered the unique LIN IP Core with...

IP Core

DCD-SEMI introduces secure & comprehensive CAN-ALL solutions for automotive

CAN-ALL implements a CAN bus controller that performs serial communication according to the CAN 2.0, CAN FD specifications, and...

Technology

DCD-SEMI presents its latest CFD solution during EXPO Dubai

DCD-SEMI along with its sister brand, the CFD SEMI unveiled its latest system during EXPO Dubai. Automotive, aerospace, transportation,...

Technology

Enhanced Serial Peripheral Interface (eSPI) Master/Slave Controller

DCD-SEMI, a leading IP Core provider and SoC design house from Poland has mastered the unique DeSPI IP Core....